Thermo King TriPac Envidia Installation Manual Download Page 60

Page: 60 / 80

Auxiliary AC Power Accessories (Option)

DC/AC Power Inverter Only

•

Follow the installation instructions supplied with the Power Inverter.

•

Connect tractor’s batteries directly to inverter as shown.

AC/DC Shore Power Converter Only

•

Follow the installation instructions supplied with the AC/DC Power Converter.

•

Connect tractor’s batteries directly to converter as shown.

Dual System DC/AC Power Inverter and AC/DC Shore Power
Converter

•

Follow the installation instructions supplied with the Power Inverter and AC/DC Power Converter.

•

Connect tractor’s batteries directly to inverter, then connect the converter to the inverter as shown.

IMPORTANT: The tractor battery power cables must always be connected directly to the DC/AC POWER INVERTER.

DC/AC Power Inverter
Connect to Tractor
Batteries

AC/DC Shore Power Converter
Connect to Tractor Batteries

Dual System
IMPORTANT: Connect Tractor
Batteries directly to the DC/AC
POWER INVERTER.

Figure 33: Auxiliary AC Power Accessories Connections

Summary of Contents for TriPac Envidia

















































































Search results

Summary of Contents for TriPac Envidia

Reviews:

Related manuals for TriPac Envidia

Brands by name

Popular brands

Thermo King TriPac Envidia, Installation Manual

Search results

Summary of Contents for TriPac Envidia

Reviews:

Related manuals for TriPac Envidia

Brands by name

Popular brands