Suzuki EN125-2A Service Manual Download Page 71

Page: 71 / 208

3-39

ENGINE

CLUTCH DRIVE PLATE

Measure the thickness and claw width of each

drive plate with vernier calipers. Replace drive

plates found to have worn down to the limit.

Vernier calipers

09900-20101

Item

Thickness

Claw width

Standard

2.9 3.1 mm

11.8 12.0 mm

Limit

2.6 mm

11.0 mm

CLUTCH DRIVEN PLATE

Measure each driven plate for distortion with a

thickness gauge. Replace driven plates which

exceed the limit.

Thickness gauge

09900-20803

Service limit

0.1 mm

CLUTCH SPRING FREE LENGTH

Measure the free length of each coil spring with a

vernier calipers, and determine the elastic

strength of each. If any one of springs is not within

the limit, replace all the springs at a time.

Vernier calipers

09900-20101

Service limit

29.5 mm

Summary of Contents for EN125-2A

















































































































































































































Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands

Suzuki EN125-2A, Service Manual

Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands