Suzuki EN125-2A Service Manual Download Page 126

Page: 126 / 208

CHASSIS

5-30

SPROCKET

Inspect the sprocket teeth for wear. If they are

worn as illustrated, replace the sprocket and drive

chain.

REAR BRAKE DRUM

Measure the brake drum I.D. to determine the

extent of wear and, if the limit is exceeded by the

wear noted, replace the drum. The value of this

limit is indicated inside the drum.

Service limit

130.7 mm

CAUTION:
Replace the brake shoes as a set, otherwise
braking performance will be adversely
affected.

BRAKE SHOE

Check the brake shoes and decide whether it

should be replaced or not from the thickness of the

brake shoe linings.

Service limit

1.5 mm

CUSHION

Inspect the cushion for wear and damage.

Summary of Contents for EN125-2A

















































































































































































































Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands

Suzuki EN125-2A, Service Manual

Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands