Suzuki EN125-2A Service Manual Download Page 81

Page: 81 / 208

3-49

ENGINE

THREAD LOCK

"1342"

99000-32050

Before mounting the oil pump, apply engine oil

to the sliding surfaces of the case, outer rotor,

inner rotor and shaft.

Apply a small quantity of THREAD LOCK

"1342" to the threaded parts of oil pump

mounting screws.

Tighten the oil pump mounting screws.

NOTE:
After mounting the oil pump in the crankcase,
rotate the pump gear by hand to see if it
turns smoothly.

Conrod holder

09910-20116

After checking the oil pump, install the oil pump

drive gear, lock washer and nut, tighten it with a

torque wrench to the specified torque and bend

up the washer.

NOTE:
This is a left-hand thread nut.

Tightening torque

40 60 N m

(4.0 6.0 kg m)

DRIVE SHAFT RETAINER

Snap ring pliers

09900-06107

Install the washer and circlip.

Bend up

Summary of Contents for EN125-2A

















































































































































































































Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands

Suzuki EN125-2A, Service Manual

Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands