Suzuki EN125-2A Service Manual Download Page 98

Page: 98 / 208

CHASSIS

5-2

Unlock the washers and remove the four bolts.

Separate the disc plate from the wheel.

CAUTION:
Do not reuse the lock washers.

Using the appropriate drift, drive out the wheel

bearings.

INSPECTION

WHEEL BEARING

Inspect the play of wheel bearings inner race by

hand while fixing it in the wheel hub.

Rotate the inner race by hand to inspect whether

abnormal noise occurs or rotating smoothly.

Replace the bearing if there is something unusual.

AXLE SHAFT

Using the special tools, check the axle shaft for

runout and replace it if the runout exceeds the limit.

Service limit

0.25 mm

Dial gauge(1/100)

Magnetic stand

V-block(100mm)

09900-20606

09900-20701

09900-21304

TIRE

(See page 2-15)

Play

Summary of Contents for EN125-2A

















































































































































































































Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands

Suzuki EN125-2A, Service Manual

Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands