Suzuki EN125-2A Service Manual Download Page 178

Page: 178 / 208

FOREWORD

SUZUKI EN125HU is designed to offer superior performance through lightness in weight

and four-stroke power. The new EN125HU represents another major advance made by

SUZUKI in four stroke motorcycles.

This service manual is prepared primarily for experienced mechanics whose job is

inspecting, repairing and servicing SUZUKI motorcycles. Apprentice mechanics and "do-

it-yourself" mechanics will also find it an extremely useful guide.

Model EN125HU, manufactured to standard specifications, is the main purpose of this

manual. However, EN125HU motorcycles distributed in your country might differ in minor

respects from the standard-specifications of EN125HU and, if they do, it is because some

minor modifications (which are of no consequence in most cases as far as servicing is

concerned) has to be made to comply with the statutory requirements of your country.

(Modifications in the 4th paragraph are as follows:)
This manual is for EN125HU motorcycle, which is a variation of EN125-2A for Mexico.

This EN125HU manual, relating only the modifications made on the basis of EN125-2A,

should be used together with "EN125-2A SERVICE MANUAL" (99500H06100-01E).

SUZUKI distributors are timely informed of our technical modifications and improvements

in this model. Please inquire our distributors for information you need.

SUZUKI MOTOR CORPORATION

JIANGMEN DACHANGJIANG GROUP CO., LTD.

Customer Service Department

Summary of Contents for EN125-2A

















































































































































































































Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands

Suzuki EN125-2A, Service Manual

Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands