Suzuki EN125-2A Service Manual Download Page 207

Page: 207 / 208

4-3

INSPECTION

Inspect wear of parts. Replace parts with obvious wear.

REFITTING

Fit kick starting device in reverse order of removal.

When fitting kick starting ratchet, align it with

the mark.

Fit kick starting bush spring, bush and clip in

the right crankcase and then fit ratchet.

When fitting ratchet, fit spring and washer on

the marked side of ratchet, turn ratchet

counterclockwise and clip ratchet pawl on the

limiting stopper.

When fitting clutch cover, bind the knurled part

of kick starting shaft end with transparent

adhesive tape to prevent it from damaging oil

seal lip

Evenly apply SUZUKI super grease to the inner

side oil seal lip.

SUZUKI super grease "A"

99000-25010

KICK STARTER

Summary of Contents for EN125-2A

















































































































































































































Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands

Suzuki EN125-2A, Service Manual

Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands