Suzuki EN125-2A Service Manual Download Page 99

Page: 99 / 208

5-3

CHASSIS

Reassemble and remount the front wheel and

front brake in the reverse order of disassembly

and removal, and also carry out the following steps:

REASSEMBLY

Apply grease to the bearings before installing.

WHEEL BEARING

SUZUKI SUPER
GREASE "A"

99000-25010

Install the wheel bearings by using the special

tool.

Bearing installer

09913-75820

NOTE:
Always use new lock washers.

Make sure that the brake disc is clean and free

of any greasy matter, After securing it in place

by tightening its bolts, be sure to lock with

specified torque.

BRAKE DISC

Tightening torque

15 25 N

(1.5 2.5 kg

Bend the washer to the bolts.

SPEEDOMETER GEAR BOX

Before installing the speedometer gear box

grease it and align groove

on the wheel hub

with two drive pawls

on the speedometer

drive gear box.

When tightening the front axle, check to be sure

that the speedometer gear box is in the position

shown.

SUZUKI SUPER
GREASE "A"

99000-25010

Summary of Contents for EN125-2A

















































































































































































































Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands

Suzuki EN125-2A, Service Manual

Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands