Suzuki EN125-2A Service Manual Download Page 140

Page: 140 / 208

INSPECTION

CHARGING OUTPUT CHECK

Start the engine and keep it running at 5 000r/min.

Using the pocket tester, measure the DC voltage

between the battery terminal

and

If the tester reads under 13.5V or over 16.0V,

check the AC generator no-load performance and

regulator/rectifier.

NOTE:
When making this test, be sure that the
battery is full-charged condition.

STD charging output

13.5V 16.0V at 5 000r/min

Pocket tester

09900-25002

AC GENERATOR NO-LOAD PERFORMANCE

Disconnect the three lead wires from the AC

generator terminal.

Start the engine and keep it running at 5 000r/min.

Using the pocket tester, measure the AC voltage

between the three lead wires.

If the tester reads under 70V, the AC generator is

faulty.

STD No-load performance

More than 70V (AC) at 5 000r/min

6-7

ELECTRICAL SYSTEM

DCV

Regulator

Rectifier

IG. switch

Battery

Summary of Contents for EN125-2A

















































































































































































































Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands

Suzuki EN125-2A, Service Manual

Search results

Summary of Contents for EN125-2A

Reviews:

Related manuals for EN125-2A

Brands by name

Popular brands