manualshive.com logo in svg

Stober SD6 Series, Manual

Share
Download
Stober SD6 Series Manual Download Page 231

ID 442426.04

231

WE KEEP THINGS MOVING

Holding brake

11

Manual SD6

11.2 Direct and indirect brake connection

There are two ways you can connect the motor holding brake to the drive 

controller:

•

Directly: 

The motor holding brake is connected directly to X5.

•

Indirectly: 

The motor holding brake is connected to the drive controller via a 

BrakeExtenderModule BX6, a contactor, a solenoid valve, a power box, 

etc.

The differences in the connection are described in section 7 Connection.

Indicate in 

F93[0] brake connection

 which connection is used for your brake. 

Note that the calculation will vary depending on the brake connection release 

time (t

release

) and the engaging time (t

engage

).

Direct connection

The following applies to a direct connection:

t

release

 = F04

t

engage

 = F05

Indirect connection

The following applies for t

release

 and t

engage

:

Release time of the connected holding brake.

When enable is activated, starting of the axis and status signals is delayed 

during the release time to prevent driving against a brake that has not been 

completely released yet.

If the holding brake is indirectly connected via a contactor (

F93

), the total 

release time t

rel

=

F04

 + 1.2*

F94

.

For STOBER motors the time should be selected so it is greater than t

2

 in the 

STOBER catalog by a factor of 1.3.

Set time of the connected holding brake.

When enable is deactivated, the power stage still remains in control during the 

set time to prevent a gravity-loaded axis from falling down.

If the holding brake is indirectly connected via a contactor (

F93

), the total set 

time t

set

=

F05

 + 1.2*

F95

.

For STÖBER motors the set time should be selected so it is greater than t

1

 in 

the STÖBER catalog by a factor of 1.3.

t

release

F04

1 2

F94

+

=

t

engage

F05

1 2

F95

+

=

F04

 t-brake release

version 0

Information

This parameter is read from and written to the electronic nameplate 

of a synchronous servo motor (SSM) with EnDat encoder if 

nameplate 

B04

 is active the first time the drive controller and motor 

are connected or when action 

B06

 is started.

F05

 t-brake set

version 0

Information

This parameter is read from and written to the electronic nameplate 

of a synchronous servo motor (SSM) with EnDat encoder if 

nameplate 

B04

 is active the first time the drive controller and motor 

are connected or when action 

B06

 is started.

Summary of Contents for SD6 Series
























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands