80
ENGLISH
EN
Original instructions for use
2.2 HYDRAULIC - OVERVIEW
The table below gives an overview of the hydrau-
lic outputs and their controls.
2.2.1 Hydraulic oil
SAE 10W-30 is recommended.
When using in winter an ISO VG 46 oil can be
used. This oil can also replace SAE 10W-30 if the
hydraulic response is slow.
2.3 IMPLEMENTS
For implements, contact an authorised dealer and
read the instructions for use supplied with the ac-
cessory.
3 DESCRIPTION
3.1 DRIVE
The machine is four wheel drive. The power from
the engine to the driven wheels is transferred hy-
draulically. The four wheels are equipped with
separate hydraulic motors. The diesel motor drives
a hydraulic pump (2:P), which pumps oil through
the hydraulic motors (2:M) of the wheels.
The hydraulic motors are connected to the hydrau-
lic pump according to fig. 2.
This means that the front and rear wheels are
forced to rotate at the same speed, but the speed on
the right and left side can vary.
3.2 STEERING
Keep all body parts away from the
machine’s pivot point when the steering
wheel is turned. There is a risk of
serious crushing injury between the
machine’s rear and front sections.
The machine has articulated steering, which is
power assisted. This means that the chassis is di-
vided into a front and rear section, which can be
turned in relation to each other.
The articulated steering means that the machine
has an extremely small turning circle and can be
easily tuned around trees and other obstacles.
3.3 SAFETY
3.3.1 Electric safety system
The machine is equipped with an electric safety
system. The safety system stops certain activities
that may be hazardous in the event of incorrect op-
eration. E.g. The engine cannot be started if the
clutch pedal/parking brake is not depressed.
The safety system’s function must
always be checked before use.
3.3.2 Warning triangle
There is a warning triangle delivered with the ma-
chine. This must be placed on the road in an emer-
gency situation in accordance with local
regulations.
Abbreviation Meaning
Dimensions
Capacity*
PTO
Output for driving front mounted implements. See
fig. 1.
2x1/2” + 3/8” return 42 l / 220 bar
PTOs
Control for operation of output for driving imple-
ments. See fig. 1.
Aux1
Output for auxiliary functions on front mounted
implements. See fig. 1.
2x1/4”
12l / 125 bar
Aux1s
Control for operating the Aux1. See fig. 1.
Aux2f
Output for auxiliary functions on front mounted
implements. See fig. 1.
2x1/4”
12l / 125 bar
Aux2r (740)
Output for auxiliary functions on rear mounted imple-
ments. See fig. 1.
2x1/4”
12l / 125 bar
Aux2S
Control for operating the Aux2f and Aux2r depend-
ing on Aux2fr See fig. 1.
Aux2fr (740) Control for activating Aux2f or Aux2r. See fig. 1.
L
Tool lift See fig. 1.
Ls
Control for operating the tool lift and lifting tools is
mounted under the cab. See fig. 1.
Summary of Contents for TITAN 740 D
Page 3: ...3 H3 H2 H1 C D E F G I9 H D1 D2 J K K1 L C D D2 D1 E F G I9 H L K K1 B A 2 4 6 3 5 7 ...
Page 5: ...5 A B D E U Ass Dis 0 1 E3 E2 E4 E1 14 16 18 15 17 19 ...
Page 6: ...6 F A B B D D E C C C E 2435 1963 1084 20 21 ...
Page 294: ...GGP Sweden AB Box 1006 SE 573 28 TRANÅS ww w sti ga com ...