Stiga TITAN 740 D, Instructions For Use Manual

Page: 82 / 294

82
ENGLISH
EN
Original instructions for use
1. Press the pedal forwards -
the machine starts to move for-
wards.
2. No load on the pedal – the
machine is stationary.
3. Pedal moved backwards –
the machine reverses.
4 The pedal is pressed towards neutral position
- the machine breaks.
In case of an emergency and the
machine does not brake as expected
when the pedal is reversed, the left
pedal (1:B6) should be used as an
emergency brake. NOTE! This puts
unnormal load on the parking brake
and shortens its service life.
3.4.2.6 Parking brake / Emergency brake (1:B6)
Never press the pedal while driving
except for in an emergency. Pressing the
pedal while driving reduces the service
life of the parking brake wich results in
a loss of functionality.
The pedal has the following
functions:
•
When stopping . Parking
brake.
•
During operation . Emergency
brake.
Indicator (1:I3) lights when the pedal is completely
depressed.
3.4.2.7 Inhibitor, parking brake (1:B7)
Never press the drive pedal (1:B5) when
parking brake is activated. This puts
unnormal load on the parking brake
and shortens its service life.
The inhibitor locks the pedal (1:B6) in the
depressed position. The function is used to
lock the machine on slopes, when trans-
porting, etc. when the engine is not run-
ning.
Locking:
1. Depress the pedal (1:B6) fully. The indicator
(1:I3) lights.
2. Press the inhibitor
3. Release the pedal.
Releasing:
1. Depress the pedal (1:B6) fully.
2. Release the pedal.
3.4.3 Controls – instrument panel
3.4.3.1 Throttle control (1:D1).
Control for setting the engine’s revs.
Front position - Full throttle - when the machine
is in operation, full throttle should always be used.
Rear position - Idling.
3.4.3.2 Ignition lock (1:D2)
The ignition lock is used for starting and stopping
the engine.
Four positions:
Preheat position: The cylinders are heat-
ed to facilitate starting. Hold in this posi-
tion as below at lower temperatures before
starting the engine.
Max 5 seconds
Stop position: The engine is stopped. The
key can be removed.
Operating position: Bypassed at start-up
and used when the engine is running.
Start position: The electric starter motor
is activated when the key is turned to the
spring-loaded starting position. Once the
engine has started, let the key return to the
operating position.
3.4.3.3 Implement lifter (1:Ls)
This control controls both the hydraulic tool lift at
the front of the machine (1:L) and the lift cylinder
for tools installed under the cab. These are con-
nected in series.
The control (1:Ls) only works when the engine is
running.
However, it can be lowered to the floating position
when the engine is off.
Never leave the machine with the imple-
ment in the transport position. Risk of
serious crushing injuries by the imple-
ment as it lowers quickly if the control
is unintentionally affected.
The lever has the four following positions:
Floating position . Move the lever to its
front position, where it locks. The imple-
ment is now lowered to its floating posi-
tion.
In the floating position, the implement
always rests against the ground at the
same pressure and can follow the con-
tours of the ground.
Use the floating position when carrying
out work.
Lowering . The implement lowers re-
gardless of its weight. The lowering
force is determined by the implement’s
weight and the hydraulic down force that
is applied when lowering.
Locking in the transport position . The
lever has returned to the neutral position
after raising and lowering. The imple-
ment is locked in the transport position.