Sony Ericsson W550c Working Instruction, Mechanical Download Page 69

Page: 69 / 128

Working Instruction

Mechanical

3/00021-1/FEA 209 544/594 B

Sony Ericsson Mobile Communications AB

69(128)

4.17

Label

4.17.1

Label Removal

•

Perform sections 2.1.1 – 2.1.2 of the Base Disassembly Procedure

Tools needed:

Pry tool

Style 2A ESD-safe tweezers (Blunt Tip)

•

Lint-free wipes

Step-by-Step Instructions

Before removing the label from a phone, print a new
label.

NOTE! The text on the new label must be fully

readable and the barcodes must be
scannable.

NOTE!

Labels only have to be removed from the
phone, if there are already two or more
labels on the phone.

NOTE!

Heating up the old label(s) with a hot air
device may make removing the labels easier.

Carefully peel the old labels from the circuit board.

NOTE!

Avoid damaging the circuit board when
removing the labels.

NOTE! Make sure that all adhesive residue is

removed. Carefully clean off any residue in
the label area with alcohol and lint-free
wipes.

Summary of Contents for W550c

































































































































Search results

Summary of Contents for W550c

Reviews:

Related manuals for W550c

Brands by name

Popular brands

Sony Ericsson W550c, Working Instruction, Mechanical

Search results

Summary of Contents for W550c

Reviews:

Related manuals for W550c

Brands by name

Popular brands