Sony Ericsson W550c Working Instruction, Mechanical Download Page 66

Page: 66 / 128

Working Instruction

Mechanical

3/00021-1/FEA 209 544/594 B

Sony Ericsson Mobile Communications AB

66(128)

4.15

System Connector

4.15.1

System Connector Removal

•

Perform sections 2.1.1 - 2.1.4 of the Base Disassembly Procedure

Tools needed:

None

Step-by-Step Instructions

Pull the system connector off of the circuit board.

4.15.2

System Connector Installation

If this part is being replaced, a new part should be used in the place of the old part when the
following steps are being performed.

Tools needed:

None

Step-by-Step Instructions

Orient the circuit board so the contact pads for the
system connector are towards you.

Orient the system connector so that side of the
connector with the row of small holes is towards you
and the side of the connector with the long slot is
towards the circuit board.

NOTE! The user accessible portion of the system

connector will oriented away from the
circuit board when the system connector is
correctly oriented.

Summary of Contents for W550c

































































































































Search results

Summary of Contents for W550c

Reviews:

Related manuals for W550c

Brands by name

Popular brands

Sony Ericsson W550c, Working Instruction, Mechanical

Search results

Summary of Contents for W550c

Reviews:

Related manuals for W550c

Brands by name

Popular brands