Sony Ericsson W550c Working Instruction, Mechanical Download Page 76

Page: 76 / 128

Working Instruction

Mechanical

3/00021-1/FEA 209 544/594 B

Sony Ericsson Mobile Communications AB

76(128)

4.21

Liquid Intrusion Indicator

4.21.1

Liquid Intrusion Indicator Removal

If a liquid intrusion indicator is activated, handle the unit according to the instructions of your
Sony Ericsson representative.

4.21.2

Liquid Intrusion Indicator Installation

There are two liquid intrusion indicators on this product. One is located on the inner base cover.
The other is located on the display flex film assembly. Use the set of instructions that applies to
the location the indicator is being installed.

Liquid Intrusion Indicator on Inner Base Cover

Tools needed:

•

Pry tool

•

Style 2A ESD tweezers (Blunt Tip)

Step-by-Step Instructions

Locate the portion of the inner base cover that
extends between the two screw bosses near the hinge
opening.

Orient the flip assembly so that the external side of
the extension that is between the two screw bosses is
towards you.

Using tweezers, place a new liquid intrusion
indicator in the center of the channel that is midway
the external side of the extension.

Summary of Contents for W550c

































































































































Search results

Summary of Contents for W550c

Reviews:

Related manuals for W550c

Brands by name

Popular brands

Sony Ericsson W550c, Working Instruction, Mechanical

Search results

Summary of Contents for W550c

Reviews:

Related manuals for W550c

Brands by name

Popular brands