Sony Ericsson W550c Working Instruction, Mechanical Download Page 77

Page: 77 / 128

Working Instruction

Mechanical

3/00021-1/FEA 209 544/594 B

Sony Ericsson Mobile Communications AB

77(128)

Step-by-Step Instructions

NOTE! Do not use your finger to apply pressure to

the liquid intrusion indicator. Using a finger
to apply pressure may cause partial
activation of the indicator.

Using the flat end of a pry tool, apply gentle pressure
to the liquid intrusion indicator to ensure a good
adhesive bond the inner base cover.

•

Perform section 3.2.4 the Flip Reassembly procedure.

•

Perform sections 2.2.2 - 2.2.4 the Base Reassembly procedure.

Liquid Intrusion Indicator on Display Flex Film Assembly

Tools needed:

•

Pry tool

•

Style 2A ESD tweezers (Blunt Tip)

Step-by-Step Instructions

Locate the square pad on the display flex film
assembly that is directly below the navigation
keypad’s dome foil.

Summary of Contents for W550c

































































































































Search results

Summary of Contents for W550c

Reviews:

Related manuals for W550c

Brands by name

Popular brands

Sony Ericsson W550c, Working Instruction, Mechanical

Search results

Summary of Contents for W550c

Reviews:

Related manuals for W550c

Brands by name

Popular brands