Sony Ericsson W550c Working Instruction, Mechanical Download Page 109

Page: 109 / 128

Working Instruction

Mechanical

3/00021-1/FEA 209 544/594 B

Sony Ericsson Mobile Communications AB

109(128)

4.34

Microphone Grommet

Replacement Procedure

•

Perform sections 2.1.1 - 2.1.3 of the Base Disassembly Procedure

•

Perform sections 3.1.1 - 3.1.4 of the Flip Disassembly Procedure

Tools needed:

•

Style 2A ESD tweezers (Blunt tip)

Step-by-Step Instructions

Orient the display carrier assembly so that the
display is away from you and locate the microphone
assembly on the display flex film.

Using style 2A tweezers, remove the microphone
grommet from the microphone assembly.

Obtain a new microphone grommet and mount it
over the microphone by using the features in the
microphone grommet and the features around the
microphone to correctly position the grommet on the
microphone.

•

Perform sections 3.2.1 - 3.2.4 of the Flip Reassembly Procedure

•

Perform sections 2.2.2 - 2.2.4 the Base Reassembly procedure.

Summary of Contents for W550c

































































































































Search results

Summary of Contents for W550c

Reviews:

Related manuals for W550c

Brands by name

Popular brands

Sony Ericsson W550c, Working Instruction, Mechanical

Search results

Summary of Contents for W550c

Reviews:

Related manuals for W550c

Brands by name

Popular brands