manualshive.com logo in svg

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 58 / 238

Share
Download
Siemens AXIOM Iconos R200 Operator'S Manual Download Page 58

System Operation

On-Off/Emergency Stop

6 

/ 32

AXD3-340.620.13.01.02

Operator Manual

Switching the system off

◆

Press the button on the generator ON/OFF console.
– The entire system and all further connected devices are immediately 

switched off.

– All started operating sequences will be interrupted and the selected 

programs will be deselected.

➩

Refer to the FLUOROSPOT Compact Operator Manual for further information.

Emergency SHUTDOWN button (installed 
on-site)

Use this shutdown method 

only in an extreme emergency

 because it is an 

un-

controlled

 process!

Data could be lost, e.g. unsaved images, exporting and filming jobs, etc. The tube 
cooling system is also disconnected from the power supply, and the tube can 
overheat.

Standby power supply

Only continuous fluoroscopy is possible in standby operation.

Pulsed fluoroscopy and all radiography modes are not possible.

“Standby power supply active” appears on the integrated generator control con-
sole in the message line.

Standby power supply inside the hospital

A standby power supply (inside the hospital) switches on if the line voltage fails. 
However, this is not as a rule without interruption and can take some time.

The system is switched off and must be switched on anew.

Battery-supported standby power supply (optional)

UPS = Uninterrupted Power Supply

An uninterrupted power supply is a battery-supported system for the standby 
power supply in the case of mains power supply failures.

If an UPS is installed for your system, then this UPS switches automatically to 
standby operation if the mains voltage fails or is too low. To prevent loss of data/
images, the imaging system remains switched on. The generator and table are 
switched off.

Summary of Contents for AXIOM Iconos R200















































































































































































































































Reviews:

No comments