Siemens AXIOM Iconos R200 Operator'S Manual Download Page 191

Page: 191 / 238

Accessories

Optional Accessories

AXIOM Iconos R200

AXD3-340.620.13.01.02

/ 54

◆

Press the tension lever (4) outward.

◆

Check that the holder is seated firmly by pulling on it.

◆

Turn the cap screws (3) on the tensioning roller toward the right.

❏

The belt will tighten.

◆

Push and pull back on the ratchet handle (1), until the belt tension is optimal.

◆

Check the belt tension on the patient once again.

Loosening the

compression belt

◆

Move the patient table to the horizontal position.

◆

Press the ratchet handle (1) back.

◆

Turn the cap screw (3) on the tensioning roller toward the left.

❏

The compression belt will loosen.

◆

Using the ratchet handle, set a lower belt tension.

Removal

◆

Move the patient table to the horizontal position.

◆

Press the ratchet handle (1) back.

◆

Turn the cap screw (3) on the tensioning roller toward the left.

❏

The compression belt will loosen.

Summary of Contents for AXIOM Iconos R200















































































































































































































































Search results

Summary of Contents for AXIOM Iconos R200

Reviews:

Siemens AXIOM Iconos R200, Operator'S Manual, Page: 191 / 238

Search results

Summary of Contents for AXIOM Iconos R200

Reviews: