![background image](http://html.mh-extra.com/html/sharp/up-5300/up-5300_service-manual_373328023.webp)
3
Terminating method.
Press the Esc key to terminate and return to the Printer diagnos-
tics menu.
2) PARALLEL2 Loop Check
1
Checking content
A loop check is performed for ER-A8RS I/O address 278H
∼
27FH
(PARALLEL2), In the loop check, the loop cable shown in Fig, 3-4
is connected between PARALLEL2 (ER-A8RS) and PARALLEL1
for testing. Set the jumpers on the PWB prior to the test as shown
in Fig. 3-6.
Setting of ER-A8RS to be tested
Fig. 3-6 Jumper pin setting
2
Display
The interruption level is displayed at XX.
If no access is allowed to PARALLEL2, the following display is
made.
3
Terminating method.
Press the Esc key to terminate and return to the Printer diagnos-
tics menu.
3) PARALLEL3 Loop Check
1
Checking content
A loop check is performed for ER-A8RS I/O address 3BCH
∼
3BEH (PARALLEL3), In the loop check, the ER-A8RS to be con-
nected is connected to the extension slot and the loop cable
shown in Fig. 3-4 is connected between PARALLEL3 (ER-A8RS)
and PARALLEL1 for testing. Set the jumpers on the PWB prior to
the test as shown in Fig. 3-6.
Setting of ER-A8RS to be tested
Fig. 3-6 Jumper pin setting
2
Display
The interruption level is displayed at XX.
If no access is allowed to PARALLEL3, the following display is
made.
3
Terminating method.
Press the Esc key to terminate and return to the Printer diagnos-
tics menu.
4) PARALLEL1 Print Check
1
Checking content
The print check is performed for the standard port PARALLEL1 at
I/O address 378H
∼
37FH. In the print check, the D-Sub 25 pin
connector is connected with a printer to allow a print pattern test.
The test procedures are as follows:
i. Data of 55H is written to I/O address 378H, and the same
address is read. If the read data is not 55H, "PARALLEL1
Channel Disabled" is displayed and the following check is not
performed.
ii. Characters of 20H
∼
7FH (ASCII code) are printed and the
line is changed.
This procedure is repeated for 5 times.
PARALLEL1 Loop Check
PARALLEL1 Channel Disabled
J9
L
H
5 7
J10
I
O
J3
J8
J4
J5
J6
J7
1
2
J18
J11
J12
J13
J14
J15
J16
J17
1
0
UP-5300 : PARALLEL1 INPUT MODE
A8RS : PARALLEL2 OUTPUT MODE
PARALLEL2 Loop Check
ACK- Signal : PASS !!(or ERROR !!)
INTERRUPT : IRQ X (or ERROR !!)
BUSY Signal : PASS !!(or ERROR !!)
PE Signal : PASS !!(or ERROR !!)
SLCT Signal : PASS !!(or ERROR !!)
ERROR- Signal : PASS !!(or ERROR !!)
STROBE- Signal : PASS !!(or ERROR !!)
AUTOFD- Signal : PASS !!(or ERROR !!)
INIT- Signal : PASS !!(or ERROR !!)
SLCTIN- Signal : PASS !!(or ERROR !!)
DATA Bus : PASS !!(or ERROR !!)
PARALLEL2 Loop Check
PARALLEL2 Channel Disabled
J9
L
H
5 7
J10
I
O
J3
J8
J4
J5
J6
J7
1
2
J18
J11
J12
J13
J14
J15
J16
J17
1
0
UP-5300 : PARALLEL1 OUTPUT MODE
A8RS : PARALLEL3 INPUT MODE
PARALLEL3 Loop Check
ACK- Signal : PASS !!(or ERROR !!)
INTERRUPT : IRQ X (or ERROR !!)
BUSY Signal : PASS !!(or ERROR !!)
PE Signal : PASS !!(or ERROR !!)
SLCT Signal : PASS !!(or ERROR !!)
ERROR- Signal : PASS !!(or ERROR !!)
STROBE- Signal : PASS !!(or ERROR !!)
AUTOFD- Signal : PASS !!(or ERROR !!)
INIT- Signal : PASS !!(or ERROR !!)
SLCTIN- Signal : PASS !!(or ERROR !!)
DATA Bus : PASS !!(or ERROR !!)
PARALLEL3 Loop Check
PARALLEL3 Channel Disabled
4 – 7
Summary of Contents for UP-5300
