![background image](http://html.mh-extra.com/html/sharp/up-5300/up-5300_service-manual_373328076.webp)
CHAPTER 7. ABOUT UTILITY
SOFTWARE AND OTHERS
Two types of UP-5300’s utility software are provided by Sharp: one is
used on UP-5300, and the other one is used on a PC (personal
computer).
1. Utility software used on UP-5300
No.
Software name
File name
1
SYSTEM INSTALLER
Sysins.exe (in Mask ROM
disk)
Outline:
The system installer executes automatically on UP-5300 boot up by
setting system SW-3 to boot from MROM Disk. It immediately waits
for receiving data from host, and processes install by communication
command from PC side’s installer.
Also, the keyboard operations are not usually required, but by con-
necting keyboard and operating as needed, communication
parameters (COM port / communication baud rate, etc) can be set up.
Furthermore, after system installer is terminated, DOS command can
be executed by going back to the command prompt. Ex: When HD is
connected, execute FDisk / Format and install to HD.
Function:
Following operation can be done.
1. Install POS application and related data files to FROM Disk,
PSRAM Disk received from PC connected with RS-232.
2. Connect UP-5300 which is already installed and UP-5300 not
installed with RS-232 and copy contents of installed machine to
other machine.
3. For optional function, operation such as changing communication
configuration, modifying AUTOEXEC.BAT / CONFIG.SYS inside
FROM / PSRAM Disk can be done.
No.
Software name
File name
2
Printer LOGO IMAGE LOADING UTILITY
Logo LDUP
Outline:
The printer logo loading utility reads logo image file (Monochrome
BMP file) and loads it against ER-01PU or UP-T80BP. To use this
utility, the POS device driver must be installed first.
Logo image is written into Flash ROM in the printer.
Loading logo image from application is needed only when changing
logo image.
Function:
Loads a logo image to the ER-01PU or UP-T80BP connected to the
UP-5300. Also, test printing can be done.
Image file to be loaded is a monochrome bitmap file.
Image data size must be smaller or equal to below list.
ER-01PU
UP-T80BP
Width (fixed)
360 dot
576 dot
Height(variable, max)
160 dot
240 dot
NOTE: At the ER-01PU, only the receipt side printer can print out
the logo data.
No.
Software name
File name
3
TOUCH PANEL CALIBRATION UTILITY
PROGRAM
CALDSRP
Outline:
The touch panel calibration utility is used to position the bottom press-
ing point of touch panel device and to align the LCDs display area.
The adjustment value returned from this utility is saved in EEPROM
inside touch panel controller. This will save the data even if the power
is shut down.
Function:
At shipment of UP-5300, the touch panel position has already been
adjusted.
To adjust it, use the touch pen of K-PDA (Keyboard enhanced Per-
sonal Digital Assistant).
PARTS CODE
PARTS NAME
MODEL
CPENP1004PCN5
Touch Pen
K-PDA ZR-xxxx series
2. Utility software used on PC (Personal
Computer)
No.
Software name
File name
1
APPLICATION INSTALL PROGRAM
(FOR MS-DOS)
APLDDOS
Outline:
POS installer is used to remotely install to the FROM / PSRAM disk
on UP-5300 connected by RS-232.
Function:
Following operations can be done.
1. Remote installation of the POS application and related data files
into the FROM Disk, PSRAM Disk on the UP-5300 connected via
RS-232 cable.
Notice
: When installing, contents of the FROM Disk and the
PSRAM Disk is erased.
No.
Software name
File name
2
APPLICATION INSTALL PROGRAM
(FOR Windows95)
APLDWIN
7 – 1
Summary of Contents for UP-5300
