manualshive.com logo in svg

Samsung S3C2451X, User Manual, Page: 500 / 756

Share
Download
Samsung S3C2451X User Manual Download Page 500

Preliminary

HSMMC CONTROLLER  

 

S3C2451X RISC MICROPROCESSOR 

21-32  

 

Preliminary product information describe products that are in development,

 

for which full characterization data and associated errata are not yet available. 
Specifications and information herein are subject to change without notice.

 

(1) When the end bit of the last data block is sent from the SD Bus to the Host 

Controller. 

(2) When beginning a wait read transfer at a stop at the block gap initiated by a 

Stop At Block Gap Request

. 

The Host Controller shall wait at the next block gap by driving Read Wait at the start 
of the interrupt cycle. If the Read Wait signal is already driven (data buffer cannot 
receive data), the Host Controller can wait for current block gap by continuing to 
drive the Read Wait signal. It is necessary to support Read Wait in order to use the 
suspend / resume function.  

(b) In the case of write transactions 

This status indicates that a write transfer is executing on the SD Bus. Changes in 
this value from 1 to 0 generate a 

Transfer Complete 

interrupt in the 

Normal 

Interrupt Status 

register.  

This bit shall be set in either of the following cases: 

(1) After the end bit of the write command. 
(2) When writing to 1 to 

Continue Request 

in the 

Block Gap Control 

register to 

continue a write transfer. 
This bit shall be cleared in either of the following cases: 

(1) When the SD card releases write busy of the last data block the Host Controller 

shall also detect if output is not busy. If SD card does not drive busy signal for 8 SD 
Clocks, the Host Controller shall consider the card drive “Not Busy”.  

(2) When the SD card releases write busy prior to waiting for write transfer as a 

result of a 

Stop At Block Gap Request

. 

1 = DAT Line Active  
0 = DAT Line Inactive 

 

CMDI
NHDA
T 

[1] 

Data Inhibit (DAT) 

(ROC)

 

This status bit is generated if either the 

DAT Line Active 

or the 

Read Transfer 

Active 

is set to 1. If this bit is 0, it indicates the Host Controller can issue the next 

SD Command. Commands with busy signal belong to 

Command Inhibit (DAT) 

(ex. 

R1b, R5b type). Changing from 1 to 0 generates a 

Transfer Complete 

interrupt in 

the 

Normal Interrupt Status 

register. 

Note: The SD Host Driver can save registers in the range of 000-00Dh for a suspend 
transaction after this bit has changed from 1 to 0. 

 
1 = Cannot issue command which uses the 

DAT 

line 

0 = Can issue command which uses the 

DAT 

line 

 

0 

CMDI
NHCM
D 

[0] 

Command Inhibit (CMD) 

(ROC)

 

If this bit is 0, it indicates the 

CMD 

line is not in use and the Host Controller can 

issue a SD Command using the 

CMD 

line.  

This bit is set immediately after the 

Command 

register (00Fh) is written. This bit is 

cleared when the command response is received. Even if the 

Command Inhibit 

(DAT) 

is set to 1, Commands using only the 

CMD 

line can be issued if this bit is 0. 

Changing from 1 to 0 generates a 

Command 

Complete 

interrupt in the 

Normal Interrupt Status 

register. If the Host Controller 

cannot issue the command because of a command conflict error (Refer to 

Command CRC Error

) or because of 

Command Not Issued By Auto CMD12 

Error

, this bit shall remain 1 and the 

Command Complete 

is not set. Status issuing 

Auto CMD12 is not read from this bit. 
 
1 = Cannot issue command 
0 = Can issue command using only 

CMD 

line 

 

0 

 

Note : Buffer Write Enable in Present register should not be asserted for DMA transfers since it generates 
Buffer Write Ready interrupt 

Summary of Contents for S3C2451X





















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments