manualshive.com logo in svg

Ricoh MPC 2800 AT-C2, Field Service Manual, Page: 657 / 856

Share
Download
Ricoh MPC 2800 AT-C2 Field Service Manual Download Page 657

4628

[Gain Adjustment: Analog]

Displays the gain value of the amplifiers on the controller for Red.

001 Latest: R Color

-

[0 to 7 / 0 / 1 digit/step]

4629

[Gain Adjustment: Analog]

Displays the gain value of the amplifiers on the controller for Green.

001 Latest: G Color

-

[0 to 7 / 0 / 1 digit/step]

4630

[Gain Adjustment: Analog]

Displays the gain value of the amplifiers on the controller for Blue.

001 Latest: B Color

-

[0 to 7 / 0 / 1 digit/step]

4631

[Gain Adjustment: Digital]

Displays the gain value of the amplifiers on the controller for Red.

001 Latest: RE Color

-

[0 to 1023 / 0 / 1 digit/step]

002 Latest: RO Color

-

4632

[Gain Adjustment: Digital]

Displays the gain value of the amplifiers on the controller for Green.

001 Latest: GE Color

-

[0 to 1023 / 0 / 1 digit/step]

002 Latest: GO Color

-

4633

[Gain Adjustment: Digital]

Displays the gain value of the amplifiers on the controller for Blue.

001 Latest: BE Color

-

[0 to 1023 / 0 / 1 digit/step]

002 Latest: BO Color

-

System Service Mode

301

8

Summary of Contents for MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments