Home
/
Ricoh
/
MPC 2800 AT-C2
/
Field Service Manual

Ricoh MPC 2800 AT-C2, Field Service Manual, Page: 310 / 856

Share

Page: 310 / 856

Ricoh MPC 2800 AT-C2 Field Service Manual Download Page 310

WebDocBox

Document server
application

Flash ROM on the
controller board

Web Uapl

WebSys

Web Service application

Flash ROM on the
controller board

Web Support

PS3

Page description language
(PostScript3)

PS3 SD card

Option PS3

PictBridge

PictBridge control

PictBridge SD card

Option PctBrgd

DESS

Security control

Flash ROM on the
controller board

Security Module

ARDF

ARDF control

ARDF

ADF

Finisher (B793)

Finisher control

Finisher (B793)

Finisher

Before You Begin

An SD card is a precision device. Always observe the following precautions when you handle SD cards:

• Always switch the machine off before you insert an SD card. Never insert the SD card into the slot

with the power on.

• Do not remove the SD card from the service slot after the power has been switched on.
• Never switch the machine off while the firmware is downloading from the SD card.
• Keep SD cards in a safe location where they are not exposed to high temperature, high humidity, or

exposure to direct sunlight.

• Always handle SD cards with care. Do not bend or scratch them. Do not let the SD card get exposed

to shock or vibration.

• Make sure that the write protection of an SD card is unlocked when you download an application to

it. If not, downloading fails and a download error (e.g. Error Code 44) occurs during a firmware
upgrade.

Keep the following points in mind when you use the firmware update software:

• “Upload” means to send data from the machine to the SD card. “Download” means to send data

from the SD card to the machine.

• To select an item on the LCD, touch the appropriate button on the soft touch-screen of the LCD, or,

press the appropriate number key on the 10-key pad of the operation panel. For example, when
“Exit (0)” shows on the screen you can touch the Exit button on the screen, or, press the



button

on the operation panel of the copier.

• Make sure that the machine is disconnected from the network to prevent a print job for arriving while

the firmware update is in progress before you start the firmware update procedure.

5. System Maintenance Reference

308

5

«
...
308
309
310
311
312
...
»

Summary of Contents for MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments