manualshive.com logo in svg

Ricoh MPC 2800 AT-C2, Field Service Manual, Page: 247 / 856

Share
Download
Ricoh MPC 2800 AT-C2 Field Service Manual Download Page 247

6. Remove the pulley and bushing [A].

7. Turn the development clutch unit [A] counter-clockwise and then pull it out (

 x 1).

8. Development clutch-Y [B] (

 x 1)

Development Clutches for M and C

1. Rear cover (

*

 "p.169")

2. PSU bracket (

*

 "p.292")

3. Open the controller box. (

*

 "p.287").

4. Drum/development motors for M and C (

*

 "p.234")

5. Disconnect the connector for each development clutch (

 x 1).

Drive Unit

245

4

Summary of Contents for MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments