manualshive.com logo in svg

Ricoh MPC 2800 AT-C2, Field Service Manual, Page: 514 / 856

Share
Download
Ricoh MPC 2800 AT-C2 Field Service Manual Download Page 514

1116

[Ends Temp. Correction]

010

Center Temp. 1: 226–

ENG

[-10 / 10 / 5 / 1 deg/step]

Specifies the temperature correction for the heating roller (center) when the paper width is
226 mm or more.
The start time of this SP can be adjusted with SP1116-018.

011

Ends Temp. 1: 226–

ENG

[-10 to 10 / 5 / 1 deg/step]

Specifies the temperature correction for the heating roller (ends) when the paper width is
226 mm or more.
The start time of this SP can be adjusted with SP1116-018.

012

Center Temp. 2: 226–

ENG

[-10 to 10 / 0 / 1 deg/step]

Specifies the temperature correction for the heating roller (center) when the paper width is
226 mm or more.
The start time of this SP can be adjusted with SP1116-019.

013

Ends Temp. 2: 226–

ENG

[-10 to 10 / 0 / 1 deg/step]

Specifies the temperature correction for the heating roller (ends) when the paper width is
226 mm or more.
The start time of this SP can be adjusted with SP1116-019.

014

Center Temp. 3: –226

ENG

[-10 to 10 / 5 / 1 deg/step]

Specifies the temperature correction for the heating roller (center) when the paper width is
less than 226 mm.
The start time of this SP can be adjusted with SP1116-020.

015

Ends Temp. 3: –226

ENG

[-10 to 10 / 0 / 1 deg/step]

Specifies the temperature correction for the heating roller (ends) when the paper width is less
than 226 mm.
The start time of this SP can be adjusted with SP1116-020.

016

Center Temp. 4: –226

ENG

[-10 to 10 / 0 / 1 deg/step]

Specifies the temperature correction for the heating roller (center) when the paper width is
less than 226 mm.
The start time of this SP can be adjusted with SP1116-021.

8. Appendix: SP Mode Tables

158

8

Summary of Contents for MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments