manualshive.com logo in svg

Ricoh MPC 2800 AT-C2, Field Service Manual, Page: 515 / 856

Share
Download
Ricoh MPC 2800 AT-C2 Field Service Manual Download Page 515

017

Ends Temp. 4: –226

ENG

[-10 to 10 / 0 / 1 deg/step]

Specifies the temperature correction for the heating roller (ends) when the paper width is less
than 226 mm.
The start time of this SP can be adjusted with SP1116-021.

018

Control Time 1: 226–

ENG

[0 to 250 / 60 / 1 sec/step]

Specifies the start time of the temperature correction that is set with SP1116-010 and -011.
The temperature correction is added when the time specified with this SP has passed after
feeding the paper.

019

Control Time 2: 226–

ENG

[0 to 250 / 0 / 1 sec/step]

Specifies the start time of the temperature correction that is set with SP1116-012 and -013.
The temperature correction is added when the time specified with this SP has passed after
feeding the paper.

020

Control Time 3: –226

ENG

[0 to 250 / 60 / 1 sec/step]

Specifies the start time of the temperature correction that is set with SP1116-014 and -015.
The temperature correction is added when the time specified with this SP has passed after
feeding the paper.

021

Control Time 4: –226

ENG

[0 to 250 / 0 / 1 sec/step]

Specifies the start time of the temperature correction that is set with SP1116-016 and -017.
The temperature correction is added when the time specified with this SP has passed after
feeding the paper.

022 M-Thick 1: Center Temp >=226

ENG

[-10 to 10 / 0 / 1 deg/step]

023 M-Thick 1: Ends Temp. >=226

ENG

024 M-Thick 2: Center Temp >=226

ENG

[-10 to 10 / 0 / 1 deg/step]

025 M-Thick 2: Ends Temp. >=226

ENG

026 M-Thick 3: Center Temp >=226

ENG

[-10 to 10 / 0 / 1 deg/step]

027 M-Thick 3: Ends Temp. >=226

ENG

[-10 to 10 / 5 / 1 deg/step]

028 M-Thick 4: Center Temp >=226

ENG

[-10 to 10 / 0 / 1 deg/step]

029 M-Thick 4: Ends Temp. >=226

ENG

System Service Mode

159

8

Summary of Contents for MPC 2800 AT-C2

























































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments