manualshive.com logo in svg

Porsche 911 CARRERA 4 -, Owner'S Manual

Share
Download
Porsche 911 CARRERA 4 - Owner'S Manual Download Page 337

Capacities

Use only fluids and fuels authorized by Porsche. Your authorized Porsche dealer will gladly advise you.

Your Porsche has been designed so that it is not necessary to mix any additives with oils or fuels.

Engine

911 Carrera, 911 Carrera 4, 911 Targa 4:

Oil change quantity without oil filter approx. 8.5 quarts / 8.0 liters

911 Carrera, 911 Carrera 4, 911 Targa 4:

Oil change quantity with oil filter approx. 8.7 quarts / 8.25 liters

911 Carrera S, 911 Carrera 4S, 911 Targa 4S:

Oil change quantity without oil filter approx. 8.7 quarts / 8.25 liters

911 Carrera S, 911 Carrera 4S, 911 Targa 4S:

Oil change quantity with oil filter approx. 9.0 quarts / 8.5 liters

Please observe the chapter ”ENGINE OIL” on page 235.

Coolant

approx. 8.45 U.S.gallons / 32 liters

Manual transmission

and differential

approx. 3.1 quarts / 2.9 liters transmission oil

Tiptronic S

approx. 9.5 quarts / 9.0 liters ATF

Differential for Tiptronic S

approx. 1.3 quarts / 1.2 liter

Fuel tank

911 Carrera, 911 Carrera S:

approx. 16.9 U.S.gallons / 64 liters

911 Carrera 4, 911 Carrera 4S, 911 Targa 4, 911 Targa 4S:

approx. 17.7 U.S.gallons / 67 liters

Fuel quality

Your engine is designed to provide optimum performance and fuel economy using

unleaded premium fuel with an octane rating of 98 RON (93 CLC or AKI).

Porsche therefore recommends the use of these fuels in your vehicle.

Porsche also recognizes that these fuels may not always be available. Be assured that your vehicle

will operate properly on unleaded premium fuels with octane numbers of at least

95 RON (90 CLC or AKI)

,

since the engine’s “Electronic Octane™ knock control” will adapt the ignition timing, if necessary.

Power steering

approx. 1.35 quarts / 1.27 liter hydraulic fluid Pentosin CHF 11 S

®

or Pentosin CHF 202

®

Brake

uid

0.48 quarts / 0.45 liters; use only Original Porsche brake fluid.

Windshield washer

approx. 2.6 quarts / 2.5 liters without headlight washer

approx. 6.3 quarts / 6.0 liters with headlight washer

Vehicle Identification, Technical Data

335

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands