Porsche 911 CARRERA 4 - Owner'S Manual Download Page 204

Page: 204 / 355

Closing the sliding roof

1. Carefully unclip both covers

with a screwdriv-

er. If the car is equipped with HomeLink, the

HomeLink buttons must be carefully unclipped

instead of the covers.

2. Unscrew the two screws

3. Fold down the cover of the lifting/sliding roof

drive at the rear. Remove the Allen key (

arrow

)

from its holder.

4. Insert the Allen key into the drive axle.

5. Press the Allen key into the drive axle, keep

it pressed and turn it clockwise until the

lifting/sliding roof is closed.

6. Remove the Allen key. Close the cover and

screw in the screws.

7. Have the fault remedied at an authorized

Porsche dealer.

Caution!

Risk of damage to the lifting/sliding roof.

After emergency operation, do not operate the

lifting/sliding roof using the rocker switch.

202

Mobile Roofs

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands

Porsche 911 CARRERA 4 -, Owner'S Manual

Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands