Porsche 911 CARRERA 4 - Owner'S Manual Download Page 167

Page: 167 / 355

Below approx. 37 °F/3 °C

The air-conditioning compressor is switched off.

Recirculating-air setting is automatically ended

after approx. 3 minutes .

Air distribution

Settings

The individual air distributions can be combined as

desired.
Recommended setting in Summer: Air distribution

to central and side vents.
Recommended setting in Winter: Air distribution to

footwell and windshield.

Air distribution to footwell

Press button

. The air flows to the footwell.

The selection appears on the display panel.

Air distribution to central and side
vents

Press button

. The air flows from the central

and side vents. Vents must be open. The

selection appears on the display panel.

Air distribution to windshield

Press button

. The air flows to the windshield.

The selection appears on the display panel.

Note on operation

On vehicles with the Sport Chrono Package

Plus, individual air conditioning settings can

be stored on your car key. Please observe the

chapter “Individual Memory” in the separate

PCM operating instructions.

General instructions for air-conditioning
compressor

–

Can switch off briefly if engine is under an

extreme load to ensure sufficient engine

cooling.

–

Switches off automatically at temperatures

below approx. 37°F /3°C and cannot be

switched on, even manually.

–

Operates most effectively with windows

closed. If the car has been in the sun for a long

time, it is a good idea to ventilate the interior

briefly with the windows open.

–

Depending on the outside temperature and

humidity, condensation can drip from the

evaporator and form a pool under the vehicle.

This is normal and not a sign of leakage.

–

If uncooled air flows out when the lowest

temperature has been set, switch off the

air-conditioning compressor and have the

fault repaired at an authorized Porsche dealer.

Controls, Instruments

165

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands

Porsche 911 CARRERA 4 -, Owner'S Manual

Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands