Porsche 911 CARRERA 4 - Owner'S Manual Download Page 304

Page: 304 / 355

Lights, Replacing Bulbs

General information

Warning!

Risk of short circuit.

Always switch off the relevant components

when changing bulbs.

Warning!

Risk of serious personal injury or death. The

Bi Xenon headlights are under high voltage

when installed.

Be careful during all work in the area of the Bi

Xenon headlights.

Caution!

Risk of damage. Bulbs of a higher wattage

can damage the lamp housing.

Only the bulbs shown in the chart may be used.

New bulbs must be clean and free from oil,

grease and fingerprints.

Therefore, never

touch bulbs with your bare hands.

Use a

cloth or soft paper while replacing bulbs.

Caution!

Risk of damage to headlights due to excessive

temperatures and abrasion.

Attach no coverings (e.g. films, “stone

guards”) in the area of the headlights.
Use soapy water only to clean light lenses

and plastic headlight lenses. In no case may

chemical cleaners or other volatile cleaning

fluids be used.
To prevent scratches, do not rub with a dry or

merely moist cloth, tissue or insect sponges.

302

Practical Tips, Emergency Service

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands

Porsche 911 CARRERA 4 -, Owner'S Manual

Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands