manualshive.com logo in svg

Porsche 911 CARRERA 4 -, Owner'S Manual

Share
Download
Porsche 911 CARRERA 4 - Owner'S Manual Download Page 247

Refueling

Fuel tank capacity is listed under “Capacities”.

Porsche does not recommend the use of fuel

additives.

Fuel is highly

ammable and harmful to

health.

Please observe the chapter ”CAPACITIES” on

page 335.

1.

Important:

Stop the engine and switch off the

ignition.

2. Slowly unscrew the tank cap. Hang the tank

cap on the plastic strap of the filler flap.

3. Insert fuel-hose nozzle fully into the filler neck

with the handle of the fuel-hose nozzle facing

down.

4. Do not add further fuel once the correctly

operated automatic fuel-hose nozzle has

switched off. Fuel could spray or could run

over in warm temperatures.

5. Replace the tank cap immediately after

refueling and turn it until you hear it and feel

it engage.

If you lose the tank cap, you must replace

it only with an original part to reduce the

possibility of a

re in the event of a collision.

Note

The oil level is automatically measured during

refuelling.
Please observe the chapter ”OIL DISPLAY AND

MEASUREMENT OF THE ENGINE OIL LEVEL”

on page 136.

Portable fuel containers

Danger!

Portable fuel containers, full or partially

empty, may leak causing an explosion, or

result in

re in case of an accident.

Never carry additional fuel in portable contain-

ers in your vehicle.

Maintenance, Car Care

245

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands