manualshive.com logo in svg

Porsche 911 CARRERA 4 -, Owner'S Manual

Share
Download
Porsche 911 CARRERA 4 - Owner'S Manual Download Page 231

Roof Transport System

Coupc only

Please follow the separate instructions for

fitting the Roof Transport System.
Only use Roof Transport Systems from the

Porsche Tequipment product range or Roof

Transport Systems which have been tested

and approved for your car by Porsche. Fitting

normal commercially available luggage racks

is not possible.

The

Porsche Roof Transport System

allows you

to carry various sports and hobby equipment. Your

authorized Porsche dealer will be pleased to tell

you about the various different uses of the Roof

Transport System.

Caution!

Completely remove the Roof Transport

System before using an automatic car wash -

risk of damage to the vehicle!
Do not exceed the maximum permitted

payload, the maximum permitted gross weight

and the maximum permitted axle loads.
Please observe the chapter ”TECHNICAL

DATA” on page 328.
Distribute load evenly, with heavy items as low

as possible. Items of luggage must not project

beyond the side of the load area.

Fix and secure every item to the basic carrier

with a rope or lashing strap (do not use elastic

rubber tensioners).
Before every trip, and at regular intervals

during long trips, check that Roof Transport

System and load are secure. Re-tighten if

necessary and secure additionally by locking.
When the Roof Transport System is loaded, the

maximum speed depends on the nature, size

and weight of the load being carried.
Driving, braking and steering behavior change

due to the higher center of gravity and the

greater wind-resistant area. You should adapt

your driving style appropriately.
Since fuel consumption and noise are

increased with the Roof Transport System

fitted, it should not remain on the vehicle if not

in use.

Mobile Roofs

229

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands