Porsche 911 CARRERA 4 - Owner'S Manual Download Page 313

Page: 313 / 355

Changing bulb for side marker light

1. Remove the cap in the wheel housing liner with

a screwdriver.

2. Insert the screwdriver into the opening in the

wheel housing liner parallel to the turn signal

housing (in direction of travel). By pressing

with the screwdriver, disengage the securing

spring of the turn signal housing.

3. Swivel out the indicator light and undo bulb

holder (bayonet lock).

4. Remove the bulb from the holder and replace

it. Insert holder. Check operation of the light.

5. Insert the turn signal’s retaining lugs

into the

side section at the front. Push in turn signal

until the securing spring

is felt to engage.

6. Press the cap into the wheel housing liner.

Practical Tips, Emergency Service

311

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands

Porsche 911 CARRERA 4 -, Owner'S Manual

Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands