manualshive.com logo in svg

Porsche 911 CARRERA 4 -, Owner'S Manual

Share
Download
Porsche 911 CARRERA 4 - Owner'S Manual Download Page 301

Replacing the remote-control battery

The battery should be changed when the range of

the radio remote control becomes smaller or when

the light-emitting diode no longer flashes when the

remote control is operated.
1. Using your finger nail or a small screwdriver,

carefully lift off the cover of the key grip

(arrow).

2. Replace the battery (paying attention to the

polarity). Replacement battery - Lithium CR

2032, 3 volts

3. Replace the cover and press together firmly.

Please observe the disposal instructions for

batteries.

Note

Please dispose of batteries in compliance with

any and all government regulations.

Practical Tips, Emergency Service

299

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands