Porsche 911 CARRERA 4 - Owner'S Manual Download Page 279

Page: 279 / 355

–

fourth four-digit code means date of manu-

facture. If, for example, the last four numbers

read 0204, the tire was produced in the 2nd

week of 2004.

C Tire ply composition and material

The number of layers in the tread and sidewalls and

their material composition.

D Maximum permissible in



ation pressure

The maximum permissible cold inflation pressure

to which a tire can be inflated.

Do not exceed the permissible inflation

pressure.

E Maximum Load rating

The maximum load in kilograms and pounds can be

carried by the tire. If you replace tires always use a

tire that has the same maximum load rating as the

factory installed tire.

F Radial

The identification indicates if the tire has radial

structure.

G Term of tubeless or tube tire

Identification for tubeless tires.

Speed code letter

The speed code letter indicates the maximum

permissible speed for the tire. This code letter is

shown on the tire sidewall.

= up to 118 mph (190 km/h)

= up to 131 mph (210 km/h)

= up to 150 mph (240 km/h)

= up to 167 mph (270 km/h)

= up to 186 mph (300 km/h)

Tip on driving

Tires with a maximum speed rating that is lower

than the specified maximum vehicle speed may be

mounted only if they bear an M+S identification on

the tire sidewall.

Please note that in addition to the winter tires,

all-season and all-terrain tires are also subject

to speed limits and bear this identification.

Inscription on light alloy wheels

Maintenance note

Protect the valve inserts against soiling with

valve caps. Use only plastic valve caps. Soiled

valve inserts can cause a gradual loss of air.

- Rim width in inches

- Rim-



ange contour code letter

- Symbol for drop-center rim

- Rim diameter in inches

- Double hump

- Rim offset in mm

Note on operation

The rim width in inches

and the rim offset

are visible from the outside. This information

can be found near the tire valve.

Practical Tips, Emergency Service

277

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands

Porsche 911 CARRERA 4 -, Owner'S Manual

Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands