Porsche 911 CARRERA 4 - Owner'S Manual Download Page 200

Page: 200 / 355

Tow-starting, towing

Please observe the chapter ”TOWING” on page

321.

Reduced driving program

A transmission fault is indicated by the following

symptoms:
–

The

4th gear

display on the instrument cluster

flashes.

–

The warning “Tiptronic emergency run”

appears on the on-board computer.

–

The transmission no longer shifts.

Warning!

Reverse gear lock monitoring is disabled in

the emergency running program. Damage

to the vehicle may result as well as loss of

control, if the vehicle is moving forward fast

enough to cause rear wheel lockup.

Do not shift into

while the vehicle is moving

forward.

Proceed as follows in the event of a transmission

fault:
1. Stop in a safe place.
2. Move selector lever to position

, switch the

ignition off and wait for 10 seconds.

3. Start the engine. 2nd gear in selector position

and reverse gear

are now available.

4. Have the fault seen to immediately at an

authorized Porsche dealer.

198

Shifting Gears

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands

Porsche 911 CARRERA 4 -, Owner'S Manual

Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands