Porsche 911 CARRERA 4 - Owner'S Manual Download Page 209

Page: 209 / 355

Emergency operation of the convertible
top

Before emergency operation

Warning!

There is danger of injury and damage during

emergency operation. There is danger

of crushing or trapping body parts at all

movable convertible top parts which could

cause serious personal injury.

Take great care when performing emergency

operation.
Do not operate the convertible top during and

after emergency operation.

Before performing emergency operation,

please check: Was the ignition switched on

and was the engine compartment lid closed

during operation of the convertible top with the

rocker switch? Are electrical fuses defective?
Please observe the chapter ”ELECTRICAL

SYSTEM” on page 292.
Remove the ignition key so that the convertible

top is not operated unintentionally.
Take screwdriver out of the tool kit.
Please observe the chapter ”LUGGAGE

COMPARTMENT (VEHICLES WITHOUT FOUR-

WHEEL DRIVE)” on page 177.

Please observe the chapter ”LUGGAGE

COMPARTMENT (VEHICLES WITH FOUR-

WHEEL DRIVE)” on page 179.
Fold the rear seat backrests forward.

Removing rear wall lining

1. Unscrew screws

from the rear wall lining.

Pull out and reposition the screwdriver insert if

necessary.

2. Grasp the rear wall lining at the cut-outs for the

safety belts and press downward. Pull rear wall

lining forward and lift up and out.

Opening convertible top compartment lid “D”

1. Take red Allen key

out of its holder.

2. Put handle of screwdriver onto Allen key

Insert Allen key into the drive axle

and turn

it counterclockwise (in direction of the arrow)

until the convertible top compartment lid

fully open. Remove the Allen key.

Mobile Roofs

207

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands

Porsche 911 CARRERA 4 -, Owner'S Manual

Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands