Porsche 911 CARRERA 4 - Owner'S Manual Download Page 311

Page: 311 / 355

Bulb for parking light A

1. Turn holder towards the left and pull it out to

the rear.

2. Pull out and replace defective bulb.
3. Push holder back in and turn towards the right.

Bulb for turn signal B

1. Turn holder counter-clockwise (bayonet lock)

and remove it.

2. Turn the defective bulb counter-clockwise

(bayonet lock) and replace it.

3. Insert holder and turn towards the right.

Bulb for fog light C

1. Press the release tab of the plug and pull plug

off.

2. Turn bulb of the defective left fog light towards

the left and the bulb of the right fog light

towards the right (bayonet lock) and replace

them.

3. Push on plug.

Practical Tips, Emergency Service

309

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands

Porsche 911 CARRERA 4 -, Owner'S Manual

Search results

Summary of Contents for 911 CARRERA 4 -

Reviews:

Brands by name

Popular brands