manualshive.com logo in svg

Porsche 911 CARRERA 4 -, Owner'S Manual

Share
Download
Porsche 911 CARRERA 4 - Owner'S Manual Download Page 285

5. Screw filler hose

B

onto the filler bottle. The

filler bottle is now open.

6. Unscrew valve cap from tire valve

F

.

7. Remove valve insert

E

from the tire valve with

valve turner

D

. Keep the valve insert in a clean

and dry place.

8. Remove plug

C

of the filler hose

B

.

9. Push filler hose onto the tire valve.
10. Hold filler bottle higher than the level of the tire

valve and press it together forcefully until the

bottle is completely emptied into the tire.

11. Pull filler hose off the tire valve.
12. Twist the valve insert firmly into the tire valve

using the valve turner.

13. Connect the compressor to the cigarette

lighter and inflate the tire to the prescribed tire

pressure.
Please observe the chapter ”TIRE PRESSURES

FOR COLD TIRES” on page 334.

14. Screw valve cap onto the tire valve.
15. Check the tire pressure after driving for

around 10 minutes. If the tire pressure is

less than 22 psi (1.5 bar), do not continue

driving. If a value of more than 22 psi (1.5 bar)

is indicated, correct the pressure to the

prescribed value.

16. Please consult your authorized Porsche

dealer.

Care Instructions

After drying, any sealant that emerges can be

peeled off like a film.

Warning!

Risk of accident, resulting in serious personal

injury or death.

Have the tire replaced by an authorized

Porsche dealer immediately.
Avoid hard acceleration and high cornering

speeds.
Do not exceed maximum speed of 50 mph

(80 km/h).
Please always observe the safety and oper-

ating instructions, which can be found in the

separate operating instructions for the sealant

and on the compressor.

A

- Front jacking point

Lifting the vehicle

Lifting the vehicle with a lifting platform or
garage lift

The car must be raised

only

at the illustrated

jacking points.

Practical Tips, Emergency Service

283

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands