manualshive.com logo in svg

Porsche 911 CARRERA 4 -, Owner'S Manual

Share
Download
Porsche 911 CARRERA 4 - Owner'S Manual Download Page 294

Electrical System

General information

In order to avoid damage and faults in electrical or

electronic systems, electrical accessories should

be installed at your authorized Porsche dealer.

Only use accessories authorized by Porsche.

Warning!

Risk of short circuit and

re, resulting in

serious personal injury or death. Replacing

fuses or relays with the engine running or the

ignition on could cause electrical shock.

Disconnect the battery during all work on the

electrical system.
Please observe the chapter ”BATTERY” on

page 295.

Relays

Defective

relays

should be changed only by an

authorized workshop.

In storage tray between the front seats

Sockets

Electrical accessories should preferably be

connected to the 12 V sockets.

Please observe the maximum power consump-

tion.

Note on operation

The tire filling compressor must be connected to

the cigarette lighter.

In the passenger’s footwell

Note on operation

The sockets and thus the connected electrical

accessories will function even if the ignition is

switched off or the ignition key is withdrawn.
If the engine is not running and the accessories are

switched on, the vehicle battery will be discharged.

Do not operate additional accessories for more

than 5 minutes when engine is off. Continuing to

do so may drain the battery such that it may go

completely dead.

Maximum power consumption for both

sockets together: 70 W.

292

Practical Tips, Emergency Service

Summary of Contents for 911 CARRERA 4 -




































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands