TROUBLESHOOTING
45
En
English
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check
the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in
use.
If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.
Symptom
Possible Cause
Remedy
No power.
• The power cord has not been connected.
• Connect to power outlet.
No sound, or sound volume is
too low.
•
AUDIO INPUT
switch is set incorrectly.
• Connection cables are not connected properly,
or are disconnected.
• Connentors or plugs are dirty.
• The rear panel
MASTER ATT.
switch is set to
–6 dB, etc.
• Set
AUDIO INPUT
switch to select the currently
playing component.
• Connect correctly.
• Clean away any dirt before connecting.
• Adjust rear panel
MASTER ATT.
switch.
No microphone sound from
BOOTH output.
• The OUTPUT TO BOOTH MONITOR (P. 42) is set
to OFF.
• Set OUTPUT TO BOOTH MONITOR (P. 42) to ON.
No digital output.
• The digital output sampling frequency (fs) does
not match the specifications of the connected
component.
• Set rear panel sampling frequency selector to
match the specifications of the connected
component.
Sound is distorted.
• Audio master output level is too high.
• Input level is too high.
• Adjust
AUDIO MASTER LEVEL
dial or the rear
panel
MASTER ATT.
switch.
• Adjust the
AUDIO TRIM
dial so that the input
level approaches 0 dB on the channel level
indicator.
Cross fader doesn’t work.
•
CROSS FADER ASSIGN
switch setting ([
A
],
[
THRU
], [
B
]) is incorrect.
• Correctly set the
CROSS FADER ASSIGN
switch
for the desired channel.
Can’t perform fader start with
DVD/CD player.
• The
FADER START
button is set to OFF.
• Rear panel
CONTROL
connector is not
connected to DVD/CD player.
• Only the rear panel
CONTROL
connector is
connected to the DVD/CD player.
• Set the
FADER START
button to ON.
• Use a control cable to connect the
CONTROL
connectors of mixer and DVD/CD player.
• Connect both the
CONTROL
connectors and
analog input connectors.
Effects don’t work.
• Effect channel selecter (CH SELECT) setting is
incorrect.
• Effect parameter 2 dial (
LEVEL/DEPTH
) is set to
[
MIN
].
• Correctly select the channel on which you wish
to apply effects.
• Adjust the effect parameter 2 dial (
LEVEL/
DEPTH
).
BPM can’t be measured.
Measured BPM value is
incorrect.
• Input level is too high, or too low.
• BPM may not be correctly measurable with
some tracks.
• Adjust the
AUDIO TRIM
dial so that the input
level approaches 0 dB in the channel level
indicator.
• Adjust other channels as well so that the input
levels approach 0 dB in the channel level
indicator.
• Strike the
TAP
button to set BPM manually.
The measured BPM value is
different from the value
published with the DVD/CD.
• Some differences may occur due to differences
in BPM detection methods.
• No remedy is necessary.
MIDI sequencer can’t be
synchronized.
• MIDI sequencer’s synch mode is not set to
“slave”.
• MIDI sequencer is not supported type.
• Set MIDI sequencer’s sync mode to “slave”.
• MIDI sequencers that do not support MIDI
timing clock cannot be synchronized.
01_SVM-1000_En.book 45 ページ ２００７年１０月１６日 火曜日 午前９時２２分
Summary of Contents for SVM 1000 - Audio/Video Mixer
Page 278: ......
