Paradyne COMSPHERE 3610 Operator'S Manual Download Page 92

Page: 92 / 310

COMSPHERE 3600 Series Data Service Units

4-12

July 1999

3610-A2-GB91-90

Table 4-4

Identity Field Descriptions

Description

Information Displayed

Model:

3610 or 3611.

S#:

Unit serial number.

DSU SW ver:

Software/firmware version residing on DSU.

Netwrk Addr:

Using ADp protocol, the ADp network address is displayed.

Using DMC protocol, the Model 3611 DSU network address is followed by
an h.

Using DPII protocol, the control DSU with a CC connection displays the
DATAPHONE II address.

DSU Rate:

Value set for DSU Rate(Kbps) configuration option. This does not appear if
the DBM is a DBM-V, DBM-S, or DBM-D.

DBM SW ver:
(Switched 56 DBM only)

The software/firmware version residing on the Switched 56 DBM.

DBM Rate:

Value set for DBM Rate(Kbps) configuration option; the DBM’s aggregate
speed. Only appears when a DBM is installed.

DBM Type:

xxx yy.y z

Type of DBM installed:

xxx can be either V (V.32 DBM or DBM-V), 4wS (4-wire Switched 56 DBM
or DBM-S), or 2wS (2-wire Switched DBM or DBM-D).

yy.y indicates the DBM’s maximum speed.

z designates whether the DBM Primary Core option was enabled.
(A P in the

z position indicates Primary Core is enabled.)

Only appears when a DBM is installed.

MUX Card:

TDM or MCMP. The type of circuit card installed. Only appears when a TDM
or MCMP circuit card is installed.

MUX App:

Currently configured application of TDM or MCMP. Possible values are TDM
or MCMP, CBrdg (central-site bridge), EBrdg (extended bridge), and None
(TDM or MCMP circuit card is disabled). Only appears when a TDM or MCMP
circuit card is installed.

MUX SW ver:

Software version residing on the TDM or MCMP circuit card. Only appears
when a TDM or MCMP circuit card is installed.

App Modul:

ASPEN. Appears when the Single-Port Async/Sync feature is installed and no
TDM or MCMP circuit card is installed.

App Modul:

CISC

or 64CC.

CISC when the Clear Channel with Integrated Secondary Channel chip is
present and the DSU software version is 5.0 or greater.

64CC when the CISC chip is not present and the DSU software version is
5.0

or greater. Only appears when a DBM is installed.

App Modul:

LPDA-2. Only appears when the SNA Diagnostic Interface option is installed.

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands

Paradyne COMSPHERE 3610, Operator'S Manual

Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands