Paradyne COMSPHERE 3610 Operator'S Manual Download Page 126

Page: 126 / 310

COMSPHERE 3600 Series Data Service Units

5-4

July 1999

3610-A2-GB91-90

To access a Digital Test from the top-level menu, make

the following selections:

•

Local

•

Test

•

DBM

•

Start

RunTim:

0:00:30

Enter

•

Use the F1 and F2 keys and the

and

keys

to select the length of time the test should run.

•

Enter (F3)

DBM Digital Tst:
Command Complete

Press the

key when the test is completed, then

display the results by selecting Displ and pressing the

key. Check for errors.

Drop the Standby connection at the control DSU, using

the Disc selection.

•

Local

•

Bckup

•

Disc

DBM: Drop Bkup
Please wait. . .

DBM: Drop Bkup
Command Complete

The Dial LED will flash rapidly to indicate the Dial

connection is being terminated. The LED goes Off when
the DBM goes on-hook (termination complete).

Run a Device Health and Status check (Devic from

H/S) on the tributary DSU again to be sure that it has
dropped Dial Backup mode.

•

Remot and Address

•

Stat

•

H/S

•

Devic

H/S:

1:23:12

19.2

DDS

If the Health and Status screen displays an arrow (

→

)

in the upper right corner of the display, press the

key

to display additional health and status information.

This completes the central-site verification procedure.

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands

Paradyne COMSPHERE 3610, Operator'S Manual

Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands