Paradyne COMSPHERE 3610 Operator'S Manual Download Page 282 | Manualshive

Page: 282 / 310

background image

COMSPHERE 3600 Series Data Service Units

K-2

July 1999

3610-A2-GB91-90

Table K-1

(2 of 2)

ANALYSIS 6510 NMS DMC Commands

NMS Command

Description

Long Status

When addressed to a DSU or DBM, returns identity information, including
device type (reported as a 2696 for a 3611 and 2656 SC for a DBM).

The MSDU firmware level is used to report the actual model number of the
DSU in the form 36.11.00. The DSU firmware level shows the DSU’s firmware
version.

Loopback Test

Causes the DSU or DBM to perform the specified loopback test. Possible
loopback tests are: DTE Loopback (Local Loopback), Local Digital Loopback,
and Remote Digital Loopback.

Returns either an A (ACK) or N (NACK).

Reset DMC

Causes the DSU to abort all test conditions and return to normal operations.
It does not enable/disable a DSU or DBM that was disabled by the DSU
Disable command.

If the addressed DSU is not in a test mode, no action is taken. Returns an
A (ACK) or N (NACK).

Strap Device

1

Reads option settings from the control DSU or DBM and returns the following
information about the DSU or DBM:

Timing
Tributary Type
Respond to RDL
RTS Control
DSR On in Local Loop
Streaming Terminal
Circuit Assurance
System Status
Elastic Store
DSU Speed

2

RS Call Control (DBM only)
DTR Call Control (DBM only)
CRQ Disconnect Control (DBM only)

Transmission Test

Causes the DSU to put the addressed tributary DSU in remote digital
loopback and transmit a test pattern. The returned data is checked for errors.

Returns Pass, Fail, or Test in Progress.

1

These selections are described in more detail in

Appendix J

.

2

A DBM speed of 12 kbps is reported as 64 kbps.

«
...
280
281
282
283
284
...
»

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3610

Brand: Campbell Pages: 90

Brand: Paradyne Pages: 22

DSL-2320B - 24 Mbps DSL Modem

Brand: D-Link Pages: 63

Zlinx ZP24D-250RM-SR

Brand: B&B Electronics Pages: 2

Brand: VisionTek Pages: 6

Brand: Black Box Pages: 101

Brand: D-Link Pages: 3

LandCell SMC-GPRS Series

Brand: CalAmp Pages: 84

Brand: Realme Pages: 24

MA01-A C 4020 Series

Brand: Ebyte Pages: 41

COMSPHERE 3821Plus

Brand: Paradyne Pages: 28

Brand: DXO Telecom Pages: 14

Brand: Xircom Pages: 28

Brand: SMC Networks Pages: 138

Brand: Raisecom Pages: 28

Brand: Sitecom Pages: 61

CheetahModem ACM 120

Brand: Accton Technology Pages: 54

Brand: TC Communications Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands