Paradyne COMSPHERE 3610 Operator'S Manual Download Page 211

Page: 211 / 310

Diagnostic Control Panel Messages Reference

C-9

3610-A2-GB91-90

July 1999

Table C-6

Subnetwork Health and Status Messages

Message

Condition

Devic

Device Failure. One of the following major alarms is in effect:

Configuration Corrupt
Device Test Failure
MUX Device Failure

DialBU

Dial Mode. Indicates DBM is active.

DialCN

Dial Connect. Indicates DBM is in Standby mode.

DialTn

Dial Tone Test failure.

Disab

Indicates DSU, DBM, or Port

nn is disabled.

DTR

DTE alarm. Data Terminal Ready lead is Off.

ExtLd

External lead alarm a or b.

Facil

DDS facility alarm. Indicates a network facility alarm.

MAJOR

Indicates a major alarm from a DATAPHONE II device.

MUX

MUX (TDM or MCMP) failure.

NoResp

The active poll list member did not respond. Probable cause: facility problem,
remote DSU problem, or poll list incorrect.

Normal

Active poll list member reports no alarm or status.

RPower

Redundant power supply alarm.

Stndby

Dial standby.

Stream

Streaming terminal.

SubSpd

Subnormal operating speed.

Test

Test mode. DSU test, DBM test, or Port

nn test.

Thresh

Threshold exceeded.

TribTm

Tributary time-out.

Trunc

Subtree truncation.

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands

Paradyne COMSPHERE 3610, Operator'S Manual

Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands