Paradyne COMSPHERE 3610 Operator'S Manual Download Page 116

Page: 116 / 310

COMSPHERE 3600 Series Data Service Units

4-36

July 1999

3610-A2-GB91-90

Transmitter Control

Transmitter Control (TxCtl) allows you to enable or

disable the DSU’s or DBM’s transmitter (DDS core), or
access the external leads of Port 1.

To access the Transmitter Control selection from the

top-level menu, make the following selections:

•

Local (F1), or Remot (F2) and Address

•

Ctrl

•

TxCtl

The Transmitter Control submenu in Local mode

differs from the one in Remote mode. Assume Local
mode in the following discussion until otherwise directed.

The following sequence of screen displays shows how

to disable the local DSU:

Change TxCtl of:
DSU

DBM

Ports

DBM is only displayed if a DBM is installed, and if the

DSU is operating in Local mode.

DSU: Enable
Enab

Disab

DSU: Disable
Command Complete

Press any key except the

key to clear the

Command Complete message.

When a control DSU is enabled, the entire network is

enabled. When the DSU is disabled, it will respond to
tests. If you abort the test, the test clears but the unit
remains disabled until you enable it.

To access the external leads (Port 1 in this example):

Change TxCtl of:
DSU

DBM

Ports

Select Ports.

Port 1: Disable
Enab

Disab

Port 1: Enable
Command Complete

The Transmitter Control submenu in Local mode

differs from the one in Remote mode.

For Remote mode, the following sequence of screen

displays shows how to disable the remote DSU:

Change TxCtl of:
Device Ports

Device: Enable
Enab

Disab

Device: Disable
Command Complete

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands

Paradyne COMSPHERE 3610, Operator'S Manual

Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands