Paradyne COMSPHERE 3610 Operator'S Manual Download Page 124

Page: 124 / 310

COMSPHERE 3600 Series Data Service Units

5-2

July 1999

3610-A2-GB91-90

In the following example, there are six tributary DSUs

with MCMP on the multichannel multipoint network with
network addresses of 3, 5, and 7.

Poll List:
Displ

Clr

Chang

Addr:

Activ

Addr:

Activ

Addr:

Activ

If a DSU’s address does not appear on the list, verify

that the missing tributary DSU is equipped with MCMP
and is configured for MCMP mode.

Proceed to the

Central-Site Procedure

section.

Verification Procedure

This section provides two procedures, one to test the

network and equipment (Central-Site Procedure) and one
to test equipment only (Remote-Site Procedure). Follow
the appropriate procedure provided.

Central-Site Procedure

Request a Device Health and Status check (Devic from

the H/S menu) from the control DSU.

•

Local

•

Stat

•

H/S

•

Devic

Check that the DDS speed is correct and that there are

no error messages (refer to

Appendix C

), then press the

key to return to the top-level menu.

To verify the diagnostic connection, request an Identity

(ID) report from each tributary in the network.

To access an Identity report from the top-level menu,

make the following selections:

•

Remot and Address

•

Stat

•

Press the

key to review the remote identity report,

then press the

key to return to the top-level menu.

Refer to

Table 4-4

for an explanation of the Identity report

descriptions.

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands

Paradyne COMSPHERE 3610, Operator'S Manual

Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands