Paradyne COMSPHERE 3610 Operator'S Manual Download Page 80 | Manualshive

Page: 80 / 310

background image

COMSPHERE 3600 Series Data Service Units

3-12

July 1999

3610-A2-GB91-90

Verification Testing

Verification testing should be performed after any

installation. To verify operation of the Model 3611 DSU,
follow the Network Verification procedure. To verify
operation of the SNA Diagnostic Interface option, follow
the SNA Diagnostic Interface Verification procedure.

After installing and configuring a circuit (including

control and tributary DSUs, the DDS network, and DBMs
and their dial connections), perform the following series
of tests from the control DSU to verify network operation
(using either the DCP or NMS):

"

Procedure

1. Request a device Identity (ID from the Status

branch) report from each tributary to ensure that
the DSU is addressed properly.

NOTE

The Model 3611 is delivered with
its network address set to 254.

2. Perform a Digital Test (on the DDS circuit) to

ensure that the network is functioning.

For a DSU equipped with DBM:

3. Use the Dial command to establish a dialed call to

the tributary to test for dial tone and that the DSU
can make and receive calls.

4. Use the

→

Dial command to switch the data to the

PSTN circuit (enter Dial Backup mode) to ensure
that both DSUs have been configured correctly.

5. Perform a Digital Test (on the PSTN circuit).

6. Drop the backup.

For further information, refer to COMSPHERE

3600 Series Data Service Units, Models 3610 and 3611,
Dial Backup Module and SNA Diagnostic Interface
Options, Applications Guide, which can be ordered.

Replacing Firmware of an
Installed Model 3611 DSU

To replace or upgrade the firmware in a Model 3611

DSU, remove the DSU circuit card assembly (CCA) and
return the CCA to the factory. The CCA will be upgraded
and then returned to you, ready for reinstallation.

Once the DSU is reinstalled and the power-up tests are

completed:

"

Procedure

1. Go to the Configuration (Confg) branch.

2. Load the appropriate factory-loaded configuration

option set: FacT for a tributary, FacC for a control,
or FacB for a central-site DSU equipped with a
digital bridge.

3. Failure to select the appropriate factory-loaded

configuration option set may cause unreliable
performance of the DSU.

«
...
78
79
80
81
82
...
»

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3610

Vantage Connect

Brand: DAVIS Pages: 12

Brand: ActionTec Pages: 2

Brand: jablotron Pages: 4

Brand: Tandy Pages: 72

Brand: StarHub Pages: 10

Brand: Motorola Pages: 29

FileMate AWUM100F

Brand: Aluratek Pages: 1

Brand: ICPDAS Pages: 16

Brand: NETGEAR Pages: 24

Brand: Four-Faith Pages: 33

Brand: Sitecom Pages: 14

Brand: Cal Amp Pages: 48

Brand: Baer Pages: 30

Brand: Hama Pages: 2

Smart Plug SP-3

Brand: MAGINON Pages: 26

Brand: SAMWOO Pages: 27

Brand: NetComm Pages: 4

Brand: Patton electronics Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands