Paradyne COMSPHERE 3610 Operator'S Manual Download

Page: 107 / 310

DSU Operations

4-27

3610-A2-GB91-90

July 1999

Displ. To clear the results of the test and reset the counters
to zero, press F2 to select Clr.

Figure 4-11. Bit Error Rate Test

Results

When the message Command Complete is displayed,

any key except the

key returns you to the Bit Error

Rate Test submenu, where the Displ and Clr selections
cause the following to be displayed:

DSU BERT: Active
Time:

0:01:26

DSU BERT: Active
Tot Error:

1017

DSU BERT: Active
Err Secs:

If the test is aborted, the top line of this display shows

Final instead of Active.

Table 4-8

defines the information

displayed after a Bit Error Rate Test has been completed.

Summary of Contents for COMSPHERE 3610























































































































































































































































































































Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands

Paradyne COMSPHERE 3610, Operator'S Manual

Search results

Summary of Contents for COMSPHERE 3610

Reviews:

Related manuals for COMSPHERE 3610

Brands by name

Popular brands